Bespoke kitchen worktops in Mallorca
You choose a worktop once and live with it for fifteen years. The useful question is not which one looks best on installation day, but which one still looks right after five years of daily use. Granite and marble are porous and need sealing; porcelain is extremely hard but cannot be repaired once an edge chips; laminate swells as soon as water finds a joint. Solid Surface behaves differently: it has no pore, it is bonded without leaving a mark however long the run, and when it is scratched or burnt it is sanded back to look as it did on day one. We fabricate and install with our own team across Mallorca.
The joint you cannot see
- Worktops of any length with no visible joint, bonded on site.
- Mitred joints between top and side, sanded until they disappear.
- Side panels running to the floor as one piece with the surface.
- Pieces carried in separately and assembled inside the house.
- No practical size limit: it does not depend on the width of your door.
This is the thing no other material does. Stone and porcelain arrive as fixed-size slabs, so once the run passes a certain length a joint appears — and that joint is always visible. Here the pieces are thermally bonded with a colour-matched adhesive and then sanded with the whole assembly: you can neither see it nor feel it.
The practical consequence is that size stops being a problem. A three-and-a-half metre island goes up the stairs in sections and ends up installed as a single block. The photograph shows it better than any explanation: four metres of worktop seen along its length, with the integrated sink and the flush hob on the way. Follow it with your eye from end to end and you will not find a single joint.
If what you want is the look of stone
- Finishes with veining and grain that read as granite, marble or limestone.
- The appearance of stone without the joint stone forces you to accept.
- No pore: it does not absorb oil or wine, and never needs sealing.
- Solid edges in the same material, with no edge banding to lift.
- Scratches polish out; in natural stone there is no remedy.
The honest comparison is this: natural stone takes direct heat and cutting better; Solid Surface takes staining, joints and time better. If pans come off the hob straight onto the surface, stone survives more. If maintenance is what concerns you, this material wins clearly.
From across the room it is not distinguishable from granite. Close up you notice a slightly warmer touch, less cold than stone, and the complete absence of a joint — which granite always has on long runs.
Integrated sink and exact cut-outs
- Bowl formed into the same piece, with no metal rim and no silicone.
- Hob cut-out made for the specific appliance model.
- Splashback rising to the wall with no trim and no angle.
- Drainer grooves milled into the surface itself, if you want them.
- Matching shelves, with the same edge detail as the worktop.
The point where almost every kitchen fails is the groove between sink and worktop. Limescale and grease collect there, and after three or four years that dark line will not come out however hard you scrub. If the bowl is part of the surface, that groove does not exist.
The photograph shows it close up: the bottom of the bowl and the worktop are the same material, joined by a continuous radius, and the steel waste sits directly in the surface. No rim, no sealant, nothing to scrape.
Colour, and not only white
- A broad range: whites, greys, blacks, sands, greens, blues and graphites.
- Saturated tones that simply do not occur in natural stone.
- Two colours combined: one around the perimeter, another on the island.
- Colour through the whole thickness: a knock reveals no different core.
- Physical samples left in the house so you see them in your own light.
Almost everyone assumes a made-to-measure worktop is white or grey. The photograph shows otherwise: a fairly traditional kitchen with the island finished in deep green. It is a little-explored route and works very well when the units are pale or timber.
One thing worth knowing before choosing: very dark and very glossy tones show fingerprints and dust more than a mid-tone matt. It is not a fault of the material — it happens to any surface — but it shapes the choice if the kitchen is in use all day.
Changing only the worktop, leaving the units
- Measuring over the base units you already have.
- Old worktop removed and the new one fitted.
- Doors, drawers and appliances left untouched.
- Usually resolved in a single day of installation.
- Fitted to walls that are almost never square.
It is one of the jobs we are asked for most, and the one that changes a kitchen most for the least building work. If the units are sound and what has aged badly is the surface — typical with laminate, which chips along the edges — there is no need to rebuild the whole kitchen.
In older homes measuring matters more than it seems, and the photograph is a good example: a sandstone wall, an original encaustic tile floor and not one right angle in sight. The piece is made to follow the real wall rather than a drawing, so it sits without a gap and without needing filler.
We make it ourselves
- Our own workshop: cutting, routing, thermoforming and polishing under one roof.
- No middlemen between the drawing and the installed piece.
- Our own installation team, with no subcontracted fitting.
- Finish checked piece by piece before anything leaves the workshop.
- Later repairs carried out by the same team that made the piece.
The photograph is of our workshop: a worktop on the extraction bench being hand-sanded with an orbital sander connected to the vacuum. Behind it, the CNC router and sheets stored on edge in A-frames.
We mention it because it shows in the result: the people who measure, fabricate and install are the same people. When something does not fit on site it is resolved there and then, without opening a file between three companies.
How the process works
First we come and look. We measure the actual opening, check how the pieces will be brought in and what condition the base units are in, because that determines whether the worktop will sit level. With those measurements and the chosen colour we prepare a fixed quotation. Fabrication happens in our workshop and installation usually takes a single day. We work across Mallorca, and we have a dedicated page for fifteen municipalities if you would like to see examples near you.
Frequently asked questions
- How much does a made-to-measure worktop cost?
- We do not quote a price per metre, and it is not because we are holding anything back: no rate card would be honest. The cost of each worktop depends on the actual linear metres, the type and colour of sheet you choose, how many bowls and cut-outs it carries, the edge detail, the workshop hours the shape demands and the difficulty of the installation. Two kitchens of the same size can come out at very different figures. That is why we measure first and give a fixed quotation: it is the only number you can genuinely decide on.
- Which material is best for a kitchen worktop?
- It depends on what you would rather live with. Natural stone takes direct heat and cutting better. Porcelain is extremely hard but cannot be repaired. Laminate is the cheapest and ages worst. Solid Surface has no pore, leaves no visible joint and is repaired by sanding, in exchange for asking you to use trivets and a chopping board. There is no absolute best, only a best for each kitchen.
- Does it scratch easily?
- It scratches, like any work surface, if you cut directly on it. The difference is what happens next: here the scratch is polished out and leaves no trace, which is impossible in stone, porcelain or laminate.
- Can I put a hot pan straight onto it?
- Better not. Prolonged direct heat can mark it. We recommend trivets, and if it ever happens, it is repaired by sanding.
- Does it need sealing or periodic treatment?
- No. Being non-porous it needs no periodic impregnation, unlike marble or granite. Water and a neutral soap are enough.
- How long does it take once measurements are taken?
- Two to three weeks from the point measurements and colour are agreed. Fabrication is done in the workshop and installation at home usually takes a single day.